This is a draft document that was built and uploaded automatically. It may document beta software and be incomplete or even incorrect. Use this document at your own risk.

Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
Storage Administration Guide / Network storage / On-demand mounting with autofs
Applies to SUSE Linux Enterprise Server 15 SP3

21 On-demand mounting with autofs

  

autofs is a program that automatically mounts specified directories on an on-demand basis. It is based on a kernel module for high efficiency, and can manage both local directories and network shares. These automatic mount points are mounted only when they are accessed, and unmounted after a certain period of inactivity. This on-demand behavior saves bandwidth and results in better performance than static mounts managed by /etc/fstab. While autofs is a control script, automount is the command (daemon) that does the actual auto-mounting.

21.1 Installation

  

autofs is not installed on SUSE Linux Enterprise Server by default. To use its auto-mounting capabilities, first install it with 

> sudo zypper install autofs

21.2 Configuration

  

You need to configure autofs manually by editing its configuration files with a text editor, such as vim. There are two basic steps to configure autofs—the master map file, and specific map files.

21.2.1 The master map file

  

The default master configuration file for autofs is /etc/auto.master. You can change its location by changing the value of the DEFAULT_MASTER_MAP_NAME option in /etc/sysconfig/autofs. Here is the content of the default one for SUSE Linux Enterprise Server: 

#
# Sample auto.master file
# This is an automounter map and it has the following format
# key [ -mount-options-separated-by-comma ] location
# For details of the format look at autofs(5).1
#
#/misc  /etc/auto.misc2
#/net -hosts
#
# Include /etc/auto.master.d/*.autofs3
#
#+dir:/etc/auto.master.d
#
# Include central master map if it can be found using
# nsswitch sources.
#
# Note that if there are entries for /net or /misc (as
# above) in the included master map any keys that are the
# same will not be seen as the first read key seen takes
# precedence.
#
+auto.master4

1

The autofs manual page (man 5 autofs) offers a lot of valuable information on the format of the automounter maps.

2

Although commented out (#) by default, this is an example of a simple automounter mapping syntax.

3

In case you need to split the master map into several files, uncomment the line, and put the mappings (suffixed with .autofs) in the /etc/auto.master.d/ directory.

4

+auto.master ensures that those using NIS (see Book “Security and Hardening Guide”, Chapter 3 “Using NIS”, Section 3.1 “Configuring NIS servers” for more information on NIS) will still find their master map.

Entries in auto.master have three fields with the following syntax: 

mount point      map name      options
mount point

The base location where to mount the autofs file system, such as /home.

map name

The name of a map source to use for mounting. For the syntax of the map files, see Section 21.2.2, “Map files”.

options

These options (if specified) will apply as defaults to all entries in the given map.

Tip
Tip: More information

For more detailed information on the specific values of the optional map-type, format, and options, see the auto.master manual page (man 5 auto.master).

The following entry in auto.master tells autofs to look in /etc/auto.smb, and create mount points in the /smb directory: 

/smb   /etc/auto.smb

21.2.1.1 Direct mounts

  

Direct mounts create a mount point at the path specified inside the relevant map file. Instead of specifying the mount point in auto.master, replace the mount point field with /-. For example, the following line tells autofs to create a mount point in the place specified in auto.smb: 

/-        /etc/auto.smb
Tip
Tip: Maps without full path

If the map file is not specified with its full local or network path, it is located using the Name Service Switch (NSS) configuration: 

/-        auto.smb

21.2.2 Map files

  
Important
Important: Other types of maps

Although files are the most common types of maps for auto-mounting with autofs, there are other types as well. A map specification can be the output of a command, or a result of a query in LDAP or a database. For more detailed information on map types, see the manual page man 5 auto.master.

Map files specify the (local or network) source location, and the mount point where to mount the source locally. The general format of maps is similar to the master map. The difference is that the options appear between the mount point and the location instead of at the end of the entry: 

mount point      options      location

Make sure that map files are not marked as executable. You can remove the executable bits by executing chmod -x MAP_FILE.

mount point

Specifies where to mount the source location. This can be either a single directory name (so-called indirect mount) to be added to the base mount point specified in auto.master, or the full path of the mount point (direct mount, see Section 21.2.1.1, “Direct mounts”).

options

Specifies an optional comma-separated list of mount options for the relevant entries. If auto.master contains options for this map file as well, these are appended.

location

Specifies from where the file system is to be mounted. It is usually an NFS or SMB volume in the usual notation host_name:path_name. If the file system to be mounted begins with a '/' (such as local /dev entries or smbfs shares), a colon symbol ':' needs to be prefixed, such as :/dev/sda1.

21.3 Operation and debugging

  

This section introduces information on how to control the autofs service operation, and how to view more debugging information when tuning the automounter operation.

21.3.1 Controlling the autofs service

  

The operation of the autofs service is controlled by systemd. The general syntax of the systemctl command for autofs is 

> sudo systemctl SUB_COMMAND autofs

where SUB_COMMAND is one of:

enable

Starts the automounter daemon at boot.

start

Starts the automounter daemon.

stop

Stops the automounter daemon. Automatic mount points are not accessible.

status

Prints the current status of the autofs service together with a part of a relevant log file.

restart

Stops and starts the automounter, terminating all running daemons and starting new ones.

reload

Checks the current auto.master map, restarts those daemons whose entries have changed, and starts new ones for new entries.

21.3.2 Debugging automounter problems

  

If you experience problems when mounting directories with autofs, it is useful to run the automount daemon manually and watch its output messages:

  1. Stop autofs. 

    > sudo systemctl stop autofs

  2. From one terminal, run automount manually in the foreground, producing verbose output. 

    > sudo automount -f -v

  3. From another terminal, try to mount the auto-mounting file systems by accessing the mount points (for example by cd or ls).

  4. Check the output of automount from the first terminal for more information on why the mount failed, or why it was not even attempted.

21.4 Auto-mounting an NFS share

  

The following procedure illustrates how to configure autofs to auto-mount an NFS share available on your network. It uses the information mentioned above, and assumes you are familiar with NFS exports. For more information on NFS, see Chapter 19, Sharing file systems with NFS.

  1. Edit the master map file /etc/auto.master: 

    > sudo vim /etc/auto.master

    Add a new entry for the new NFS mount at the end of /etc/auto.master: 

    /nfs      /etc/auto.nfs      --timeout=10

    This tells autofs that the base mount point is /nfs, the NFS shares are specified in the /etc/auto.nfs map, and that all shares in this map will be automatically unmounted after 10 seconds of inactivity.

  2. Create a new map file for NFS shares: 

    > sudo vim /etc/auto.nfs

    /etc/auto.nfs normally contains a separate line for each NFS share. Its format is described in Section 21.2.2, “Map files”. Add the line describing the mount point and the NFS share network address: 

    export      jupiter.com:/home/geeko/doc/export

    The above line means that the /home/geeko/doc/export directory on the jupiter.com host will be auto-mounted to the /nfs/export directory on the local host (/nfs is taken from the auto.master map) when requested. The /nfs/export directory will be created automatically by autofs.

  3. Optionally comment out the related line in /etc/fstab if you previously mounted the same NFS share statically. The line should look similar to this: 

    #jupiter.com:/home/geeko/doc/export /nfs/export nfs defaults 0 0

  4. Reload autofs and check if it works: 

    > sudo systemctl restart autofs
    # ls -l /nfs/export
total 20
drwxr-xr-x  5 1001 users 4096 Jan 14  2017 .images/
drwxr-xr-x 10 1001 users 4096 Aug 16  2017 .profiled/
drwxr-xr-x  3 1001 users 4096 Aug 30  2017 .tmp/
drwxr-xr-x  4 1001 users 4096 Apr 25 08:56 manual/

    If you can see the list of files on the remote share, then autofs is functioning.

21.5 Advanced topics

  

This section describes topics that are beyond the basic introduction to autofs—auto-mounting of NFS shares that are available on your network, using wild cards in map files, and information specific to the CIFS file system.

21.5.1 /net mount point

  

This helper mount point is useful if you use a lot of NFS shares. /net auto-mounts all NFS shares on your local network on demand. The entry is already present in the auto.master file, so all you need to do is uncomment it and restart autofs: 

/net      -hosts
> sudo systemctl restart autofs

For example, if you have a server named jupiter with an NFS share called /export, you can mount it by typing 

> sudo cd /net/jupiter/export

on the command line.

21.5.2 Using wild cards to auto-mount subdirectories

  

If you have a directory with subdirectories that you need to auto-mount individually—the typical case is the /home directory with individual users' home directories inside—autofs offers a clever solution.

In case of home directories, add the following line in auto.master: 

/home      /etc/auto.home

Now you need to add the correct mapping to the /etc/auto.home file, so that the users' home directories are mounted automatically. One solution is to create separate entries for each directory: 

wilber      jupiter.com:/home/wilber
penguin      jupiter.com:/home/penguin
tux      jupiter.com:/home/tux
[...]

This is very awkward as you need to manage the list of users inside auto.home. You can use the asterisk '*' instead of the mount point, and the ampersand '&' instead of the directory to be mounted: 

*      jupiter:/home/&

21.5.3 Auto-mounting CIFS file system

  

If you want to auto-mount an SMB/CIFS share (see Chapter 20, Samba for more information on the SMB/CIFS protocol), you need to modify the syntax of the map file. Add -fstype=cifs in the option field, and prefix the share location with a colon ':'. 

mount point      -fstype=cifs      ://jupiter.com/export